Training & Stories

Aussie Pro Runner Smart Console: Zwift Setup, Garmin Sync & Test Results

Aussie Pro Runner Smart Console setup guide for pairing with Zwift

Take your Pro Runner sessions into Zwift—and keep the finished workout in Garmin Connect. Pro Runner owner Luis Mario Rodriguez tested the Bluetooth Smart Console in his own training setup. Here is what he found, how to reproduce the connection, and how to make sense of different distance readings.

What worked in Luis’s test

  • The Smart Console connected directly to Zwift as the running speed source.
  • No separate footpod or Bluetooth bridge was needed in his iPhone setup.
  • A heart-rate strap connected separately, while the console display stayed available.
  • A saved Zwift run appeared in his linked Garmin Connect account.

The distinction: the console supplies live speed to Zwift; Zwift sends the saved activity to Garmin Connect. This test did not establish a direct live speed connection from the console to a Garmin watch.

Pair the console · Add heart rate · Save to Garmin · See the results · Download the report · Troubleshoot

About this report: Luis purchased his Pro Runner, and Aussie Fitness Pros supplied the console at no charge. He prepared his report voluntarily, with no fee paid for the report. What a bloody legend! This article is our practical summary of his November 2–5, 2026 testing, shared with his permission.

What you need

  • An Aussie Pro Runner fitted with the compatible Bluetooth Smart Console.
  • A supported device running Zwift, with Bluetooth enabled.
  • Optional: a compatible heart-rate monitor.
  • Optional: a Garmin Connect account if you want finished runs saved there.

Luis used Zwift on an iPhone, a Garmin fēnix 7 Pro Solar, and a Garmin HRM-Pro. His console appeared as TF0B-S001-A177, with firmware V88.09.02 and software V1.2.1. Device names and app screens can vary. If you are upgrading an older Pro Runner, contact us to confirm console compatibility before ordering.

1. Pair the Smart Console with Zwift

  1. Wake the console. Walk on the belt for about 10–15 seconds.
  2. Open Zwift. Enable Bluetooth and allow the app Bluetooth access if prompted.
  3. Choose Run, then Run Speed. Open the Paired Devices screen and select your console from the available speed sources.
  4. Confirm the connection. Start a route at an easy pace and check that Zwift responds as you change belt speed.

Keep the console selected as Run Speed if you want Zwift to use its speed data. Heart rate and cadence are optional connections; every tile does not need to be connected before you run.

Three steps to pair the Aussie Pro Runner Smart Console with Zwift: wake the console, open Zwift, and select Run Speed.
Illustrated setup guide based on Luis’s test. The example screen shows the search state before pairing; app screens may vary.

Luis also reported that his devices reconnected on later sessions. If yours do not, wake the console and open Paired Devices to select it again.

2. Add heart rate if you want it

Wear and activate your compatible heart-rate strap, then select it under Zwift’s Heart Rate tile. Leave the console selected under Run Speed. In Luis’s test, the HRM-Pro supplied heart rate separately from the console’s speed connection.

Optional heart-rate setup: connect a compatible strap under Heart Rate while keeping the console under Run Speed.
Heart rate is optional. The console and strap serve different roles in this setup.

3. Save the Zwift workout to Garmin Connect

  1. Sign in to Zwift’s Connections settings.
  2. Connect your Garmin account and authorize the connection.
  3. Complete your workout in Zwift.
  4. End the run and select the option to save/upload it.
  5. Check Garmin Connect for the saved activity. Syncing may take time.

Luis verified this with a 1.79-mile Zwift activity in Garmin Connect. You do not need to record a second workout on a watch for this account-to-account transfer. Simply moving the belt with an app open does not create a saved workout.

Link Garmin Connect to Zwift, end and save the run, then check Garmin Connect for the completed activity.
Illustrated workflow based on the saved activity documented in Luis’s report.

The useful workaround: keep your watch for alerts

Luis wanted wrist alerts during training, so he also recorded a separate treadmill activity on his Garmin watch while Zwift recorded the console data. This let him use his watch’s alerts and Zwift together.

If you use this approach, configure alerts for your own training needs and watch model. Check for duplicate entries after saving: a watch workout and a synced Zwift workout can both appear in Garmin Connect. Review the information you want to retain before removing a duplicate. Recording on both devices does not make their pace or distance measurements identical.

What the distance test showed

During the November 5 session, Luis recorded the following readings:

Reported readings from one session
Metric Console Zwift Garmin watch
Distance 2.89 km
(about 1.80 mi)
1.79 mi 1.60 mi
Reported duration 41:00 38:17 40:49

Read Luis’s original console report

Explore Luis Mario Rodriguez’s test setup, measurements, screenshots and conclusions in the original document he supplied.

Download Luis’s original report (PDF)

Original report · 7 pages · 2.43 MB. Written by Luis Mario Rodriguez and shared unchanged. The report presents his observations and conclusions; this article provides additional setup guidance and context for interpreting the results.

The console’s 2.89 km converts to approximately 1.796 miles, close to Zwift’s displayed 1.79 miles. That is encouraging consistency between the console reading and the app using its data.

This is an owner field test, not a laboratory accuracy certification. The console and Zwift used the same underlying speed source, and the recorded sessions had different start times and durations. Their agreement does not independently establish absolute distance accuracy, and the average paces are not a like-for-like comparison.

Why did the watch show 1.60 miles?

The watch recording used a different measurement method. Garmin explains that compatible HRM straps estimate running pace and distance using the user profile and motion detected with each stride. That estimate can differ from the console data supplied to Zwift.

Calibration, sensor selection, movement patterns, and recording timing are factors to check. This session does not isolate how much each contributed to the difference.

A harder-feeling run does not create a mileage conversion. The 1.79 versus 1.60-mile result does not prove a percentage increase in effort or calories. For useful comparisons, keep your speed source, resistance setting, and recording procedure consistent, and track perceived effort or heart rate separately.

For watch-based distance, follow Garmin’s calibration guidance for your watch and HRM. Garmin supports calibration on compatible setups; verify the reference distance before using it to adjust a sensor.

Quick troubleshooting

  • Console not showing? Move the belt to wake it, check Bluetooth permissions, then reopen Run Speed.
  • It worked before? Close other apps or disconnect another device that may already be using the console’s Bluetooth connection.
  • Heart rate missing? Check that the strap is active and paired separately under Heart Rate.
  • Garmin activity missing? Confirm the account link and that you saved the Zwift run. Allow time for syncing; check Zwift’s integration help if it still does not appear.
  • Distances differ? Check kilometers versus miles, the selected speed source, and the recording times before changing calibration.

Still stuck? Email sales@aussiefitnesspros.com with a photo of your console, the device running Zwift, and a screenshot of the pairing screen.

Make your next session a connected session

Explore the Smart Console upgrade and check compatibility with your Pro Runner.

View the Aussie Pro Runner Smart Console

Sources and setup help

Test observations and readings: Luis Mario Rodriguez, Zwift Treadmill & HRM Assessment, November 2026. Thank you to Luis for documenting his setup and sharing the results.

This guide covers the setup Luis tested. It does not establish compatibility with every app, watch, or console revision. Zwift and Garmin are third-party platforms; features and screens may change.

Previous
90 days to make it a lifestyle

Leave a Comment

Your email address will not be published.